|
FXO / FXS / Telecom Smart Paging Interface -
FXI-1
|
 |
| Status: Beta |
|
|
.jpg) Viking’s FXI-1 universal paging interface allows you to provide paging from virtually any type of phone system instead of from a microphone. You can also provide background music and electronic night bell over the audio system.
The FXI-1 provides 30V talk battery for interfacing with an FXO or unused analog line input/trunk port. With the flip of a switch, the unit can connect to a FXS or PABX station ring trip port. No power supply is required in this mode. In the event that it must be connected to a “dry” 600 ohm paging port, the built-in voice activation (VOX) is in control. This configuration is useful when interfacing with systems that do not provide a paging contact closure, such as Panasonic, South Western Bell, Intertel, etc.
In all modes the FXI-1 provides normally open or normally closed relay contacts to activate the central paging amplifier equipment or connect to an external background music source. After paging, the FXI-1 auto disconnects on CPC, busy signal, silence or default disconnect timer. An electronic night bell over paging feature can be activated from a momentary phone system contact closure (FXO and page port mode only).
|
| more info... |
|
|
12 Circuit Ground to Loop Start Converter
-
GLS-12
|
|
| Status: Beta |
|
|
.jpg) Model GLS-12 is designed to allow up to 12 standard telephone sets, multi-line key systems or other loop start equipment to be connected to and operate on two-wire ground start CO trunk lines. The GLS-12 provides the CO ground start line with the signalling required to draw dial tone when the loop start equipment goes off-hook. Incoming calls are not affected by the GLS-12 and ring directly to the loop start devices.
|
| more info... |
|
|
Night Bell Over Paging Adapter -
K-600F
|
|
| Status: Beta |
|
|
.jpg) The K-600F eliminates the installation of multiple bells, relays, and power supplies, wherever night bells, loud ringing, or emergency tones are required. The K-600F provides an existing paging amplifier with a pleasant electronic warble tone each time it receives ring voltage from an analog PABX/KSU extension.
The K-600F requires no external power supply and provides a floating 600 ohm audio output. Paging In and Out terminals are provided to allow automatic switching between paging and warble audio when used with an existing paging installation. A set of N.O. / N.C. relay contacts are provided that switch in cadence with the ring signal. Volume and tone controls are also provided.
|
| more info... |
|
|
Line Powered Off Hook,
Ring and Message
Waiting Indicator -
LPL-1
|
|
| Status: Beta |
|
|
.jpg) The Viking model LPL-1 connects to any standard analog
phone line or phone system’s analog station port* to provide
visual “Ring” Indication, “On The Phone” indication and
“Message Waiting**” indication. The LPL-1 won’t have you
guessing which phone is ringing in busy offices. The large
flashing LED can be seen up to 100 feet away. When used
with a headset on an analog phone, you can end those nagging
interruptions that occur when associates don’t realize
you are on the phone because you are using a headset. The
LPL-1 will light steady indicating to everyone that you are on
the phone, flash during ringing or fast flash to indicate message
waiting**.
*Caution: The LPL-1 is not compatible with digital station ports.
**When installed on phone systems with standard 90VDC message waiting voltage.
|
| more info... |
|
|
Telephone Line Powered Ringer -
LPR-1
|
|
| Status: Beta |
|
|
.jpg) This auxiliary electronic ringer operates on any analog line that provides a minimum of 40 volts 20-30 Hz AC ring voltage. Nominal 3 KHz warble provides up to 92 dB SPL @ 1 meter. The LPR-1 can be connected via screw terminals or modular RJ-11 jack. A volume control and a 7 foot modular cord are provided. No power supply is required.
CLICK HERE to preview factory sounds for the LPR-1
|
| more info... |
|
|
Proximity Card Reader -
PROX-1
|
|
| Status: Beta |
|
|
.jpg) The model PROX-1 is a HID compatible 125KHz proximity card reader and is designed to be mounted directly to a metal door or window frame (mullions), making it ideal for applications requiring an access credential. The proximity card reader transmits data in 26-Bit Wiegand format, making it compatible with any of the Wiegand equipped Viking entry controllers.
The PROX-1 delivers non-contact read ranges up to 6 inches (152 mm), and operates from 5 to 14 VDC. Physical size is a compact 3.2 x 1.7 x 0.70 inches (80 x 43 x 17 mm). Mounting is simplified with horizontal and vertical mounting slots, which allow the reader to be conveniently adjusted and leveled. To allow both indoor and outdoor operation the electronics are sealed in tamper resistant epoxy potting. Concealing the mounting hardware, the PROX-1 ships with both Black and Ash (Off-White) covers standard.
|
| more info... |
|
|
Proximity Card Reader with Built-in Keypad -
PROX-2
|
|
| Status: Beta |
|
|
.jpg) The model PROX-2 is designed to be mounted directly to standard single-gang wall box, and integrates both a HID compatible 125KHz proximity card reader and keypad into a single-unit making it ideal for applications requiring an access credential and/or personal identification number (PIN).
The proximity card reader and keypad of the PROX-2 both transmit data in 26-Bit Wiegand format, making it compatible with any of the Wiegand equipped Viking entry controllers. The keypad is based upon cutting-edge, non-mechanical, capacitive technology, which, unlike membrane keypads, includes no moving parts prone to early failure. Advanced keypad enhancements include fully potted circuit board (EWP), keys with blue LED backlighting, raised key outlines and pip on the 5-key.
The PROX-2 delivers non-contact read ranges up to 6 inches (152 mm), and operates from 5 to 14 VDC. Physical size is a compact 4.6 x 3 x 0.70 inches (117 x 77 x 18 mm). Mounting is simplified with horizontal and vertical mounting slots, which allow the reader to be conveniently adjusted and leveled. To allow both indoor and outdoor operation the electronics are sealed in tamper resistant epoxy potting. Concealing the mounting hardware, the PROX-2 ships with both Black and Ash (Off-White) covers standard.
|
| more info... |
|
|
Medium Range Proximity Card Reader
-
PROX-3
|
|
| Status: Beta |
|
|
.jpg) The model PROX-3 is a high performance medium range HID compatible 125KHz proximity card reader. The PROX-3’s compact size yet long read range of up to 16 inches* make it ideal for parking control, gate access, turnstiles, etc. It is designed to be mounted directly to a wall, post, single gang electrical box or use an optional mounting kit for attaching it to a gooseneck pedestal. Mounting is simplified with horizontal and vertical mounting slots, which allow the reader to be conveniently adjusted and leveled. To increase vandal resistance the chassis is a single piece design with the mounting screws concealed behind a UV stable label.
The proximity card reader transmits data in 26-Bit Wiegand format, making it compatible with any of the Wiegand equipped Viking entry controllers. The PROX-3 is equipped with Enhanced Weather Protection (EWP) for outdoor installations where the unit is exposed to precipitation or condensation. With its sealed connections and fully potted electronics the PROX-3 is designed to meet an IP66 Ingress Protection Rating. For more information, see DOD# 859.
|
| more info... |
|
|
Network Enabled Relay Controller -
RC-4
|
|
| Status: Beta |
|
|
.jpg) The RC-4 Network Enabled Relay Controller provides networked control of four remote relays via a web interface. The same interface can be used to check the status of four contact closures at the remote location.
Relays can be toggled on or off, or user-programmed timed closures can be activated. Two levels of user access permit selected users to have full operational and programming rights while others have operational control but not programming capability.
|
| more info... |
|
|
Oil Rubbed Bronze Single Gang Mountable Camera -
VCAM-2-BN
|
|
| Status: Beta |
|
|
.jpg) The VCAM-1 and VCAM-1IR are high resolution color composite video cameras. Their compact size will allow mounting in even the smallest locations. The extreme temperature rating of this camera, makes it ideal for mounting in outdoor locations in a water tight enclosure.
The VCAM-2 is a compact, high resolution color composite video camera mounted behind a standard single gang wall plate. The VCAM-2 is available in two finishes: Brushed Stainless Steel (VCAM-2-SS) and Oil Rubbed Bronze (VCAM-2-BN). The extreme temperature rating and Enhanced Weather Protection make this camera ideal for mounting in outdoor locations.
The VCAM-1 is not compatible with IR illuminators and is a direct replacement for the cameras included in the following Viking models: AES-2005, E-35, E-50, E-65, E-75, K-1205, K-1705-3 and W-3005.
The VCAM-1IR has a day/night OLP (optical low pass) filter and is compatible with standard 840-850nM IR illuminators. The VCAM-1IR is the same size as the VCAM-1 allowing it to be used in all of the above Viking products.
All cameras are equipped with Enhanced Weather Protection (EWP) for outdoor installations where the unit is exposed to precipitation or condensation. The VCAM-1, VCAM-1IR and VCAM-2 feature sealed connections, as well as an epoxy potted circuit board.
|
| more info... |
|
|
Brushed Stainless Steel Single Gang Mountable Camera -
VCAM-2-SS
|
|
| Status: Beta |
|
|
.jpg) The VCAM-1 and VCAM-1IR are high resolution color composite video cameras. Their compact size will allow mounting in even the smallest locations. The extreme temperature rating of this camera, makes it ideal for mounting in outdoor locations in a water tight enclosure.
The VCAM-2 is a compact, high resolution color composite video camera mounted behind a standard single gang wall plate. The VCAM-2 is available in two finishes: Brushed Stainless Steel (VCAM-2-SS) and Oil Rubbed Bronze (VCAM-2-BN). The extreme temperature rating and Enhanced Weather Protection make this camera ideal for mounting in outdoor locations.
The VCAM-1 is not compatible with IR illuminators and is a direct replacement for the cameras included in the following Viking models: AES-2005, E-35, E-50, E-65, E-75, K-1205, K-1705-3 and W-3005.
The VCAM-1IR has a day/night OLP (optical low pass) filter and is compatible with standard 840-850nM IR illuminators. The VCAM-1IR is the same size as the VCAM-1 allowing it to be used in all of the above Viking products.
All cameras are equipped with Enhanced Weather Protection (EWP) for outdoor installations where the unit is exposed to precipitation or condensation. The VCAM-1, VCAM-1IR and VCAM-2 feature sealed connections, as well as an epoxy potted circuit board.
|
| more info... |
|
